tuhi/README.md

TUHI
=====

Tuhi is a DBus session daemon that connects to and fetches the data from the
Wacom ink range (Spark, Slate, Folio, Intuos Paper, ...). The data is
provided to clients in the form of JSON, any conversion to other formats
like SVG must be done by the clients.

Tuhi is the Maori word for "to draw".

Supported Devices
-----------------

Devices tested and known to be supported:

* Bamboo Spark
* Bamboo Slate
* Intuos Pro Paper

Registering devices
-------------------

For a device to work with Tuhi, it must be registered first. This is
achieved by holiding the device button for 6 or more seconds until the blue
LED starts blinking. Only in that mode can Tuhi detect it during
`Searching` and register it.

Registration sends a randomly generated UUID to the device. Subsequent
connections must use that UUID as identifier for the tablet device to
respond. Without knowing that UUID, other applications cannot connect.

A device can only be registered with one application at a time. Thus, when a
device is registered with Tuhi, other applications (e.g. Wacom Inkspace)
cannot not connect to the device anymore. Likewise, when registered with
another application, Tuhi cannot connect.

To make the tablet connect again, simply re-register with the respective
application or Tuhi, whichever desired.

This is not registering the device with some cloud service, vendor, or
other networked service. It is a communication between Tuhi and the firmware
on the device only. It is merely a process of "your ID is now $foo" followed
by "hi $foo, I want to connect".

The word "register" was chosen because "pairing" is already in use by
Bluetooth.

Packages
--------

Arch Linux: [tuhi-git](https://aur.archlinux.org/packages/tuhi-git/)

Installation
------------

```
 $> git clone http://github.com/tuhiproject/tuhi
 $> cd tuhi
 $> python3 setup.py install
 $> tuhi
```

TUHI requires Python v3.6 or above.

Units used by this interface
----------------------------

* Physical distances for x/y axes are in µm from the sensor's top-left
  position. (Note that on the Spark and on the Slate at least, the sensor
  is turned 90 degrees clockwise, so (0,0) is at the 'natural' top-right
  corner)
* Stylus pressure is normalized to a range of [0, 0xffff], inclusive.
* Timestamps are in seconds in unix epoch, time offsets are in ms after the
  most recent timestamp.

DBus Interface
--------------

The following interfaces are provided:

```
org.freedesktop.tuhi1.Manager

  Property: Devices (ao)
      Array of object paths to known (previously registered, but not necessarily
      connected) devices. Note that a "registered" device is one that has been
      initialized via the Wacom SmartPad custom protocol. A device does not
      need to be paired over Bluetooth to register.

  Property: Searching (b)
      Indicates whether the daemon is currently searching for devices.

      This property is set to True when a StartSearching() request initiates
      the search for device connections. When the StartSearching() request
      completes upon timeout, or when StopSearching() is called, the property
      is set to False.

      When a pariable device is found, the UnregisteredDevice signal is sent to
      the caller that initiated the search process.

      Read-only

  Property: JSONDataVersions (au)
      Specifies the JSON file format versions the server supports. The
      client must request one of these versions in Device.GetJSONData().

      Read-only, constant

  Method: StartSearch() -> ()
      Start searching for available devices ready for registering
      for an unspecified timeout. When the timeout expires or an error
      occurs, a SearchStopped signal is sent indicating success or error.

      If a client that successfully initated a listening process calls
      StartSearching() again, that call is ignored and no signal is
      generated for that call.

  Method: StopSearch() -> ()
      Stop listening to available devices ready for registering. If called after
      StartSearch() and before a SearchStopped signal has been received,
      this method triggers the SearchStopped signal. That signal indicates
      success or an error.

      If this method is called before StartSearch() or after the
      SearchStopped signal, it is ignored and no signal is generated.

      Note that between calling StopSearch() and the SearchStopped signal
      arriving, UnregisteredDevice signals may still arrive.

  Signal: UnregisteredDevice(o)
      Indicates that a device can be registered. This signal may be
      sent after a StartSearch() call and before SearchStopped(). This
      signal is sent once per available device and only to the client that
      initiated the search process with StartSearch.

      When this signal is sent, a org.freedesktop.tuhi1.Device object was
      created, the object path is the argument to this signal.

      A client must immediately call Register() on that object if
      registering with that object is desired. See the documentation for
      that interface for details.

      When the search timeout expires, the device may be removed by the
      daemon again. Note that until the device is registered, the device is not
      listed in the managers Devices property.

  Signal: SearchStopped(i)
      Sent when the search has stopped. An argument of 0 indicates a
      successful termination of the search process, either when a device
      has been registered or the timeout expired.

      If the errno is -EAGAIN, the daemon is already searching for devices
      on behalf of another client. In this case, this client should wait for
      the Searching property to change and StartSearching() once the
      property is set to False.

      Once this signal has been sent, all devices announced through
      UnregisteredDevice signals should be considered invalidated. Attempting to
      Register() one of the devices after the SearchStopped() signal may result
      in an error.

      In case of error, the argument is a negative errno.

org.freedesktop.tuhi1.Device

  Interface to a device known by tuhi. Each object in Manager.Devices
  implements this interface.

  Property: BlueZDevice (o)
      Object path to the org.bluez.Device1 device that is this device.
      Read-only

  Property: Dimensions (uu)
      The physical dimensions (width, height) in µm
      Read-only

  Property: BatteryPercent (u)
      The last known battery charge level in percent. This charge level is
      only accurate when the BatteryState is other than Unknown.

      When the BatteryState is Unknown and BatteryPercent is nonzero, the
      value is the last known percentage value.

      Read-only

  Property: BatteryState (u)
      An enum describing the battery state. Permitted enum values are

        0: Unknown
        1: Charging
        2: Discharging

      'Unknown' may refer to a state that could not be read, a state
      that has not yet been updated, or a state that has not updated within
      a daemon-internal time period. Thus, a device that is connected but
      does not regularly send battery updates may eventually switch to
      'Unknown'.

      Read-only

  Property: DrawingsAvailable (at)
      An array of timestamps of the available drawings. The timestamp of
      each drawing can be used as argument to GetJSONData(). Timestamps are
      in seconds since the Epoch and may be used to display information to
      the user or sort data.
      Read-only

  Property: Listening (b)
      Indicates whether the daemon is currently listening for the device.

      This property is set to True when a StartListening() request initiates
      the search for device connections. When the StartListening() request
      completes upon timeout, or when StopListening() is called, the property
      is set to False.

      When the user press the button on the device, the daemon connects
      to the device, downloads all drawings from the device and disconnects 
      from the device.

      If successfull, the drawings are deleted from the device. The data is
      held by the daemon in non-persistent storage until the daemon is stopped
      or we run out of memory, whichever happens earlier.
      Use GetJSONData() to retrieve the data from the daemon.

      DO NOT RELY ON THE DAEMON FOR PERMANENT STORAGE

      When drawings become available from the device, the DrawingsAvailable
      property updates to the number of available drawings.
      When the button is pressed multiple times, any new data is appended
      to the existing list of drawings as long as this property is True.

      Read-only

  Property: Live(b)
      Indicates whether the device is currently in Live mode. When in live
      mode, the device does not store drawings internally for a later sync
      but instead fowards the events immediately, similar to a traditional
      graphics tablet. See StartLive() for more details.

      Read-only

  Method: Register() -> (i)
      Register the device. If the device is already registered, calls to
      this method immediately return success.

      Otherwise, the device is registered and this function returns success (0)
      or a negative errno on failure.

  Method: StartListening() -> ()
      Listen for data from this device and connect to the device when it
      becomes available. The daemon listens to the device until the client
      calls StopListening() or the client disconnects, whichever happens
      earlier.

      The ListeningStopped signal is sent when the listening terminates,
      either on success or with an error. A client should handle this signal
      to be notified of any errors.

      When the daemon starts listening, the Listening property is updated
      accordingly.

      If a client that successfully initated a listening process calls
      StartListening() again, that call is ignored and no signal is
      generated for that call.

  Method: StopListening() -> ()
      Stop listening for data on this device. If called after
      StartListening(), this method triggers the ListenStopped signal.
      That signal indicates success or an error.

      If this method is called before StartListening() or after the
      ListeningStopped signal, it is ignored and no signal is generated.

      Note that between calling StopListening() and the ListeningStopped
      signal arriving, the property DrawingsAvailable may still be updated
      and it's the responsibility of the client to fetch the JSON data.

  Method: StartLive(fd: h) -> (i)
      Starts live mode on this device. This disables offline storage of
      drawing data on the device and instead switches the device to a mode
      where it immediately reports the pen data, similar to a traditional
      graphics tablet.

      The LiveStopped signal is sent when live mode terminates, either on
      either on success or with an error. A client should handle this signal
      to be notified of any errors.

      When live mode enables, the Live property is updated accordingly.

      If a client that successfully initated a listening process calls
      StartListening() again, that call is ignored and no signal is
      generated for that call.

      The fd argument is a file descriptor that will be used to forward
      events to. The format is the one used by the Linux kernel's UHID
      device, see linux/uhid.h for details.

  Method: StopLive() - >()
      Stop live mode on this device. If called after StartLive(), this
      method triggers the LiveStopped signal.  That signal indicates
      success or an error.

      If this method is called before StartLive() or after the LiveStopped
      signal, it is ignored and no signal is generated.

      Note that between calling StopLive() and the LiveStopped signal
      arriving, the device may still send events. It's the responsibility of
      the client to handle events until the LiveStopped signal arrives.

  Method: GetJSONData(file-version: u, timestamp: t) -> (s)
      Returns a JSON file with the drawings specified by the timestamp
      argument. The requested timestamp must be one of the entries in the
      DrawingsAvailable property value. The file-version argument specifies
      the file format version the client requests. See section JSON FILE
      FORMAT for the format of the returned data.

      Returns a string representing the JSON data from the last drawings or
      the empty string if the timestamp is not available or the file format
      version is outside the server-supported range advertised in
      Manager.JSONDataVersions.

  Signal: ButtonPressRequired()
      Sent when the user is expected to press the physical button on the
      device. A client should display a notification in response, if the
      user does not press the button during the (firmware-specific) timeout
      the current operation will fail.

  Signal: ListeningStopped(i)
      Sent when the listen process has stopped. An argument of 0 indicates a
      successful termination, i.e. in response to the client calling
      StopListening(). Otherwise, the argument is a negative errno
      indicating the type of error.

      If the errno is -EAGAIN, the daemon is already listening to the device
      on behalf of another client. In this case, this client should wait for
      the Listening property to change and StartListening() once the
      property is set to False.

      If the error is -EBADE, the device is not ready for registering/in
      listening mode and registration/listening was requested. In
      this case, the client should indicate to the user that the device
      needs to be registered first or switched to listening mode.

      If the error is -EACCES, the device is not registered with the daemon
      or incorrectly registered. This may happen when the device was
      registered with another host since the last connection.

      The following other errnos may be sent by the daemon:
      -EPROTO: the daemon has encountered a protocol error with the device.
      -ETIME: timeout while communicating with the device.

      These errnos indicate a bug in the daemon, and the client should
      display a message to that effect.

  Signal: LiveStopped(i)
      Sent when live mode is stopped. An argument of 0 indicates a
      successful termination, i.e. in response to the client calling
      StopLive(). Otherwise, the argument is a negative errno
      indicating the type of error.

      If the errno is -EAGAIN, the daemon has already enabled live mode on
      device on behalf of another client. In this case, this client should
      wait for the Live property to change and StartLive() once the property
      is set to False.

      If the error is -EBADE, the device is not ready for live mode, most
      likely because it is in registration mode. In this case, the client
      should indicate to the user that the device needs to be registered
      first.

      If the error is -EACCES, the device is not registered with the daemon
      or incorrectly registered. This may happen when the device was
      registered with another host since the last connection.

      The following other errnos may be sent by the daemon:
      -EPROTO: the daemon has encountered a protocol error with the device.
      -ETIME: timeout while communicating with the device.

      These errnos indicate a bug in the daemon, and the client should
      display a message to that effect.
```

JSON File Format
----------------

The current file format version is 1. A server may only support a subset of
historical file formats, this subset is advertized as list of versions in
the **org.freedesktop.tuhi1.Manager.JSONDataVersions** property. Likewise, a
client may only support a subset of the possible formats. A client should
always pick the highest format supported by both the client and the server.

Below is the example file format (with comments, not present in the real
files). The JSON objects are "drawing" (the root object), "strokes",
"points".  Pseudo-code is used to illustrate the objects in the file.

```
class Drawing {
        version: uint32
        devicename: string
        dimensions: [uint32, uint32] // x/y physical dimensions in µm
        timestamp: uint64
        strokes: [ Stroke, Stroke, ...]
}
```

The **strokes** list contains all strokes of a single drawing, each stroke
consisting of a number of **points**.

```
class Stroke {
        points: [Point, Point, ...]
}
```

The **points** list contains the actual pen data.

```
class Point {
        toffset: uint32
        position: [uint32, uint32]
        pressure: uint32
}
```

An expanded file looks like this:

```
{
   "version" : 1,                       // JSON file format version number
   "devicename":  "Wacom Bamboo Spark", 
   "dimensions": [ 100000, 200000],      // width/height in µm
   "timestamp" : 12345,
   "strokes" : [
        {
            "points":  [
               // all items in a point are optional. Unknown dictionary
               // entries must be ignored as future devices may add
               // new axes.
               { "toffset" : 12366, "position" : [ 100, 200 ], "pressure" : 1000 },
               { "toffset" : 12368, "pressure" : 800 },
               { "toffset" : 12366, "position" : [ 120, 202 ] },
             ]
        },
        {  "points" : ... }
    ]
}
```

Device notes
============

When following any device notes below, replace the example bluetooth
addresses with your device's bluetooth address.

Bamboo Spark
------------

The Bluetooth connection on the Bamboo Spark behaves differently depending
on whether there are drawings pending or not. Generally, if no drawings are
pending, it is harder to connect to the device. Save yourself the pain and
make sure you have drawings pending while debugging.

### If the device has no drawings available:

* start `bluetoothctl`, commands below are to be issued in its interactive shell
* enable discovery mode (`scan on`)
* hold the Bamboo Spark button until the blue light is flashing
* You should see the device itself show up, but none of its services
  ```
  [NEW] Device E2:43:03:67:0E:01 Bamboo Spark
  ```
* While the LED is still flashing, `connect E2:43:03:67:0E:01`
  ```
  Attempting to connect to E2:43:03:67:0E:01
  [CHG] Device E2:43:03:67:0E:01 Connected: yes
  ... lots of services being resolved
  [CHG] Device E2:43:03:67:0E:01 ServicesResolved: yes
  [CHG] Device E2:43:03:67:0E:01 ServicesResolved: no
  [CHG] Device E2:43:03:67:0E:01 Connected: no
  ```
  Note how the device disconnects again at the end. Doesn't matter, now you
  have the services cached.
* Don't forget to eventually turn disable discovery mode off (`scan off`)

Now you have the device cached in bluez and you can work with that data.
However, you **cannot connect to the device while it has no drawings
pending**. Running `connect` and pressing the Bamboo Spark button shortly
does nothing.

### If the device has drawings available:

* start `bluetoothctl`, commands below are to be issued in its interactive shell
* enable discovery mode (`scan on`)
* press the Bamboo Spark button shortly
* You should see the device itself show up, but none of its services
  ```
  [NEW] Device E2:43:03:67:0E:01 Bamboo Spark
  ```
* `connect E2:43:03:67:0E:01`, then press the Bamboo Spark button
  ```
  Attempting to connect to E2:43:03:67:0E:01
  [CHG] Device E2:43:03:67:0E:01 Connected: yes
  ... lots of services being resolved
  [CHG] Device E2:43:03:67:0E:01 ServicesResolved: yes
  [CHG] Device E2:43:03:67:0E:01 ServicesResolved: no
  [CHG] Device E2:43:03:67:0E:01 Connected: no
  ```
  Note how the device disconnects again at the end. Doesn't matter, now you
  have the services cached.
* `connect E2:43:03:67:0E:01`, then press the Bamboo Spark button re-connects to the device
  The device will disconnect after approximately 10s. You need to start
  issuing the commands to talk to the controller before that happens.
* Don't forget to eventually turn disable discovery mode off (`scan off`)

You **must** run `connect` before pressing the button. Just pressing the
button does nothing unless bluez is trying to connect to the device.

**Warning**: A successful communication with the controller deletes the
drawings from the controller, so you may not be able to re-connect.